Configurar ADSL Masmovil en router comtrend ar-5315u

ADVERTENCIA:
Al resetear el router se cargará la configuración que tenía por defecto. Por  lo tanto perderemos cualquier ajuste que hayamos cambiado.
(Por ejemplo, direccionamiento IP, configuración dhcp, ssid y clave de la wifi, etc...)

ANOTAD LO QUE SEA NECESARIO ANTES DE PROCEDER



PASO 1 - RESETEAR Y ACCEDER AL ROUTER

Conectamos y encendemos el router
Pulsamos con un clip en el botón de RESET de la parte trasera durante 5 segundos

Accedemos al router desde un navegador introduciendo  http://192.168.1.1

Usuario:
admin
contraseña:
admin



PASO 2 - BORRAR WAN SERVICE

Advanced setup -> Wan service


Marcar las casillas y pulsar en Remove



PASO 3 - BORRAR ATM INTERFACE

advanced setup -> layer 2 interface -> atm interface



marcar las casillas y borrar igual que en el paso anterior



PASO 4 - crear interface atm

En advanced setup -> layer 2 interface -> atm interface

Pulsamos en Add

Interface atm0

Vpi 8

Vci  32

DSL Latency
 Path0 (Fast)

Select DSL Link Type (EoA if for ppoe)
EoA

Encapsulation mode = LLC/SNAP-BRIDGING

Service category = UBR  without PCR

Resto de opciones como aparecen:
Weighted round robin

Default queue weight = 1
Default queue precedence = 8

VC WRR Weight = 1
VC precedence = 8




PASO 5 - crear WAN SERVICE

Advanced setup -> wan service

Add


Next


Select a layer 2 interface for this service

Note: For ATM interface, the descriptor string is (portId_vpi_vci)
For PTM interface, the descriptor string is (portId_high_low)
Where portId=0 --> DSL Latency PATH0
portId=1 --> DSL Latency PATH1
portId=4 --> DSL Latency PATH0&1
low =0 --> Low PTM Priority not set
low =1 --> Low PTM Priority set
high =0 --> High PTM Priority not set
high =1 --> High PTM Priority set

Escogemos la atm0/0_8_32





Next

En wan service configuration
Escogemos
PPP OVer ethernet

Enter 802.1P Priority [0-7]: 0

Enter 802.1Q VLAN ID [0-4094]: 20

Network protocol selection = ip v4 only



Next

En PPP Username and password

PPP Username:    adsl@masmovil
PPP Password:    masmovil
PPPoE Service Name:  
Authentication Method: AUTO

Enable NAT = SI
Enable Firewall = SI
resto desactivadas





IMPORTANTE :
HACER SCROLL HACIA ABAJO
QUE LLEGUE AL FINAL DE LA PÁGINA

MTU 1488

resto opciones desactivadas

Enable PPP Debug Mode
Bridge PPPoE Frames Between WAN and Local Ports

Multicast Proxy
Enable IGMP Multicast Proxy
No Multicast VLAN Filter






Next

En Routing -- Default Gateway


Selected Default Gateway Interfaces

ppp0_1

Next


DNS Server Configuration

Select DNS Server Interface from available WAN interfaces:

añadimos ppp0_1





Next


WAN Setup - Summary

Nos muestra un resumen de la configuración:

Connection Type: PPPoE
NAT: Enabled
Full Cone NAT: Disabled
Firewall: Disabled
IGMP Multicast: Disabled
Quality Of Service: Disabled



Pulsamos en  Apply / Save


PASO 6 - reiniciar
Vamos a  management -> reboot




PASO 7 - comprobaciones

Si todo ha ido bien en Device info tenemos que ver algo como esto:

Line Rate - Upstream (Kbps): 1022
Line Rate - Downstream (Kbps): 16329
LAN IPv4 Address: 192.168.1.1
Default Gateway: ppp0.1
Primary DNS Server: 212.166.64.1
Secondary DNS Server: 8.8.8.8
Date/Time: Thu Jan 1 00:01:51 1970



En Wan Info tenemos que ver que se nos ha asignado una IP  del rango del CGNAT (100.65.x.x)




Hacemos un test de velocidad en

http://www.speedtest.net/es/result/6269810601

Comentarios

Entradas populares de este blog

Cómo saber el UUID de un equipo

Reducir el tamaño de install.wim a menos de 4 GB

Configurar Cobian Backup 11 Gravity para que envie correos desde gmail